Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Rotobrush Coil Cleaning: The Long Beach Owner’s Guide
We stock Rotobrush-compatible coil cleaning parts at our Long Beach shop and typically have them installed on site within 48 hours of your call. Installed pricing for Rotobrush coil cleaning equipment runs $180 to $420 depending on whether you need a brush head, drive assembly, or the full coil cleaning bundle. Most owners discover the problem the same way: the brush spins slower than it used to, leaves streaks on the coil fins, or stops spinning entirely mid-job.
Coil cleaning on a Rotobrush system is what separates a decent duct cleaning from a half-done one. The coil is where the air actually gets cold or warm, and if the Rotobrush head can’t reach and scrub it properly, you’re paying for airflow that’s no cleaner than when we started. Roy Castellanos has pulled enough caked-on coil grime out of Long Beach units to know exactly what a worn coil cleaning attachment does to your system’s efficiency. Clean coils transfer heat. Dirty coils fight it, and your energy bill eats the difference.
Which Rotobrush Models This Applies To
The Rotobrush coil cleaning attachments we service fit the AiR+ and BRH series units, along with the older R500 and R2000 platforms still running in plenty of Long Beach homes. The compatibility gotcha most owners miss: the coil cleaning head is not universal across Rotobrush generations. The drive shaft diameter changed between the BRH and AiR+ lines, so a head that fits a 2015 unit will not seat properly on a newer machine. Always check the serial plate on the drive motor housing before ordering anything.
Rotobrush uses a specific spline pattern on their coil cleaning shafts. Aftermarket heads exist, and some are fine, but we’ve seen too many aftermarket brushes shed bristles into coil fins because the backing plate flexed under load. For coil cleaning specifically, we recommend OEM Rotobrush heads or the one aftermarket brand we’ve tested that holds tolerance. Hollis Air Duct Long Beach is an independent service provider, not a Rotobrush dealer, which means we install what actually works, not what a franchise agreement tells us to push.
Styles & brands we work with
Signs Your Rotobrush Coil Cleaning Is Failing
- Brush head slows under load. The drive coupling is worn, usually from repeated exposure to the dust and moisture that collects in Long Beach evaporator coils near the coast. The motor is fine; the coupling isn’t transferring torque anymore.
- Streaks or missed bands on the coil surface. Bristles have flattened or broken off. A coil cleaning head that leaves stripes is doing half the job, and the untreated bands trap the same grime you’re trying to remove.
- Rattling or vibration when the head spins free. The bearing in the guide wheel has play. This is the first component to fail on Rotobrush coil cleaning attachments used in humid environments, which describes most of Long Beach from June through October.
- The head won’t seat or locks at an angle. The quick-connect receiver is clogged with debris or the splines are rounded. Forcing it only damages both halves of the connection.
- Brush bristles are matted with a waxy film. This is coil cleaner residue that wasn’t rinsed properly after the last job. Once bristles mat, they stop scrubbing and start smearing.
Replacement Cost & What’s Included
For Rotobrush coil cleaning in Long Beach, expect these installed ranges:
- Replacement brush head (OEM): $180 to $260 installed
- Drive coupling and guide wheel assembly: $120 to $200 installed
- Full coil cleaning bundle (head, coupling, guide wheel, shaft): $320 to $420 installed
The price you’re quoted is the price you pay. Written down, before any work starts. The part is itemized separately from labor, so you see exactly what you’re paying for. Every Rotobrush coil cleaning repair we do carries a one-year written warranty. If that replacement head fails within 365 days, we come back and make it right at no charge, including the second visit. That’s the 365-Day Done Right Promise, and it’s in writing on every job.
DIY or Call Us?
You can safely inspect the brush head without tools. Pull it off the drive shaft, look at the bristles, check the guide wheel for side-to-side play, and wipe the splines clean. That tells you what’s wrong. Replacing the internal drive coupling is where DIY goes sideways. The coupling sits under spring tension, and if it releases while your hand is in the wrong position, it’ll take a chunk of skin with it. We’ve also seen owners cross-thread the quick-connect and strip the receiver, which turns a $200 repair into a $420 one.
If the bristles are matted or the head streaks, that’s a swap we can do in under an hour. Call (562) 548-7365 and we’ll match the part to your Rotobrush serial number before we even schedule the visit.
How Much Does Rotobrush Coil Cleaning Replacement Cost in Long Beach?
Installed Rotobrush coil cleaning replacement in Long Beach runs $120 to $420 depending on what failed. A bare brush head is on the low end; a full coil cleaning bundle with shaft and coupling is at the top of the range. The written quote covers parts, labor, and the one-year warranty. Call (562) 548-7365 and we’ll give you a firm number before any work begins.
See the difference
Before
After
Before
After
Before
AfterHow Long Does a Rotobrush Coil Cleaning Head Last in Long Beach?
In coastal Long Beach air, a Rotobrush coil cleaning head typically lasts 18 to 24 months of regular use before bristles start flattening or the coupling develops play. Proximity to the harbor accelerates the wear because salt-laden air corrodes the quick-connect faster than inland units. If you store the attachment in a garage without climate control near the water, expect the shorter end of that range. Call (562) 548-7365 if you want us to assess what you have before it fails mid-job.
Can a Worn Rotobrush Coil Cleaning Head Be Repaired Instead of Replaced?
Most of the time, no. Once bristles are flattened or matted with cleaner residue, there’s no reliable way to restore them. The guide wheel bearing can sometimes be replaced individually if caught early, but by the time most owners notice, the coupling has worn too. We’ll always tell you if a repair is possible instead of a replacement, but for coil cleaning heads, replacement is the honest answer more often than not. Get the part matched by calling (562) 548-7365.
Do You Stock Rotobrush Coil Cleaning Parts Locally in Long Beach?
Yes. We keep Rotobrush coil cleaning brush heads, couplings, guide wheels, and complete bundles on the truck and in our Long Beach shop. We also stock parts for Lennox, Trane, and Carrier systems, but Rotobrush is what we run on our own cleaning rigs, so that’s what we carry deepest. The advantage of local stock is that we can usually have your attachment back in service within two days. Call (562) 548-7365 with your model number and we’ll confirm the part is on hand before you commit to anything.
Get Your Rotobrush Coil Cleaning Attachment Fixed in Long Beach
A Rotobrush coil cleaning attachment that isn’t scrubbing properly means every cleaning job you run leaves coil fins half-done. We match the part to your serial number, price it in writing before work starts, and cover it for a full year. Clean ducts aren’t a luxury – they’re just what the system needs to do its job. Call (562) 548-7365 for a free estimate and we’ll have your Rotobrush back on the job.
Written by Roy Castellanos, Owner, Hollis Air Duct Long Beach at Hollis Air Duct Long Beach, serving Long Beach and nearby areas.